Chamfering Spokeshave

TIIH liiol is raLher like a spokeshavc 1>ti< !i;ls a CUtlCr SuCll ¿15 ii used ill the metal spokes have, fonctt, of coureet ermi that the chamfer ■, Of ¡n r»y number QfchBmft?Bh Will lie worked to c*actly the same depüj. This is achieved by regulating their pOsittlNlS. Sinei IllC ffllCri .lie piovided with a projection which works iknfi a groove l.^Pi Fig. 'i.ir they arc bound to remain exactly at right angles with rhc sole.

Construction, ■ The mou[h ti^r niiL\L accommodate a 3¿-in, cutter. Prcpar« a piece of wiod Ei I finish inin. by ijf in, ivy t in. Mark ihc surface which u ill he the sole at id updo

Ttif potpnte cfthlf r»f is [A craHe ((tewferi to be wojft«| HI nr, txtjLi deptf ontj «accrf can osftf fat (Mir itrrjijhl ir l iirh'-:'-'/ ciiruej. foi a cjflfave {(jfvt, IWiKfr. iftt ftlfe witHiii Jiffrf to be ffriitaitti amt thii wqpJrf fifittisimte iha^i^ jhe jranrgfcte fwxa to luit. J( wiU „ork cfMf « □ tlop: in if it* n-porf ii cut way healtf □[ the tieft die tpokeshav* an iw token riph( Uiranjii.

Ttif potpnte cfthlf r»f is [A craHe ((tewferi to be wojft«| HI nr, txtjLi deptf ontj «accrf can osftf fat (Mir itrrjijhl ir l iirh'-:'-'/ ciiruej. foi a cjflfave {(jfvt, IWiKfr. iftt ftlfe witHiii Jiffrf to be ffriitaitti amt thii wqpJrf fifittisimte iha^i^ jhe jranrgfcte fwxa to luit. J( wiU „ork cfMf « □ tlop: in if it* n-porf ii cut way healtf □[ the tieft die tpokeshav* an iw token riph( Uiranjii.

■^^■■.i^imii ■■■■■,■■..' .'■iii'ii.i'.iL'.iiM

TIC. I. INYALUABLF TOOL WTH Y USES IN TH( WORtSHO-P

Although pr- ma ■ ily Ter wnrl.nj JUrtlAlfl, Eh L 1«l lJ.i ;r ntf Hjiilnirv ipc-i »Lh],*

lYBffc ^ fHTtd. lit Ihn CUM Ih. eIM n( t,r.lt, jr. d.r^hid It [|L<d n Ir'. cuK.r

■^^■■.i^imii ■■■■■,■■..' .'■iii'ii.i'.iL'.iiM

FIG. 2. DTT.iiLi OF THt iLit-WC, FRnCM

TIC. I. INYALUABLF TOOL WTH Y USES IN TH( WORtSHO-P

Although pr- ma ■ ily Ter wnrl.nj JUrtlAlfl, Eh L 1«l lJ.i ;r ntf Hjiilnirv ipc-i »Lh],*

lYBffc ^ fHTtd. lit Ihn CUM Ih. eIM n( t,r.lt, jr. d.r^hid It [|L<d n Ir'. cuK.r it draw in the mouih Encju These ^ork otu at i in. apart, die front One being A in. from I Etc front. Sin« die Cutter slopes kick at ^ de^. ll is simple lo mark the opening of the escapement at ihe Lop by drawing a line at th?. end at 4jdcg. ami tarrying it through to the top'.

iiore a series of holes ftom the mouth right through the wood, usiiiji a bit slt^hily under ¿in. Now ehop away I he ivattt from the mouth and escapement, Efritsh o(f with a keen chisel, making die surface on which tlie cutter Ijeds perfectly Ihit.

Using a jig in, cutter, work ;i groove from end to end on the stJe surtax, [| might in- J ill.; deep. Bored hole tlnouijh the Ix-d to lake the bolt which fixes the cutter in position. Position it so that the cutter Can be fitted generously Ibrwaid. Thus the cutler can SI ill be iC/JltlKOid V/i pitfl ;■

j _ FBONT ELF^TtJfJ 1

O 0 VIIW FROM arNfATH

. 1

'i

-—risS

L

b

fid. 3. eleyvn^n. pians and il=ction with main siz ei d-h awn to

0 0

Responses

  • Dora
    How to make a spokeshave pdf?
    6 months ago

Post a comment