Main Illustration By Ian Hall

"A mule chest is a sophistication of one of furniture's most basic forms; the storage box"

Modifications

I've been waiting for an opportunity to make one of these for years, and then two of my regular clients, Chris and Mel, made the mistake of telling me that they wanted a sideboard, but had no idea what kind.

above: Shelf is adjustable, finely calculated to accommodate bottles below and glasses above

LEFT! Carcass subassemblies: side panel is tongue and grooved with a loose-fitted fielded panel; frame is mortice and tenoned -note notch for side facings chest

LEFT! Carcass subassemblies: side panel is tongue and grooved with a loose-fitted fielded panel; frame is mortice and tenoned -note notch for side facings

"You want something like a mule chest" I said.

The only drawback of the mule chest is the lift-up lid, making it unsuitable for display objects on top and requiring more leaning over to access the contents than most people want to be involved with. The panelled front, however, may be subverted into doors without visual clashing, and this allows the top to be fixed.

I drew two versions of this piece for the clients to choose from, one with square-panelled doors and another featuring the broken-arch panels shown here. With a little nudging, they chose the right one!

Selection

Unless you are very familiar with this kind of work, make up a full-size drawing on MDF, or similar, before starting. It is easier to work out the relationship of the parts with a pencil in your hand than with a saw.

With traditional oak furniture, the quality of the timber used is of paramount importance. The heavy

"it is easier to work out the relationship of the parts with a pencil in your hand than with a saw"

visual blocks involved must be broken up by colour, grain and texture to avoid a sombre, funereal look.

In this I was the beneficiary of a happy accident - the timber supplier failed to deliver when arranged, and by way of apology supplied me with their very best selected quartered oak - T bought about 8 cu ft of generous 25mm (lin) thick stuff for this chest, which allowed for further selection as I made up the cutting list.

above: Shelf is adjustable, finely calculated to accommodate bottles below and glasses above right: Side panel biscuited ready for assembly -position mid-panel biscuits using drawer divider as guide

There is only one way to get a cutting list out of waney-edged English oak while obtaining the best visual effect for critical components - and that is to lay out the boards on the workshop floor and mark out the parts with wax crayon, nesting them together to avoid wastage.

At least that's how I used to do it when I had a workshop floor to speak of. Now things are more cramped I have to stand all the boards on their long edges, flipping through them like a card index. It is worth spending time on this stage, though, to avoid the best figure ending up on internal parts!

Construction

Although this is a classic piece, I departed from traditional construction quite severely in places. The carcass sides and doors have, in place of mortice and tenons, tongue and groove joints. This is quite safe in this instance, as the solid panels add strength, and the stiles and rails are very wide, allowing a long joint. Glue technology is so much more advanced now tftan in the 18th century that, provided that the gluing area is large, mechanical strength is less important than it once was. Polyurethane glue, such as Gorilla Glue or Titebond Polyurethane, was used throughout and is a good performer, which doesn't leave black stains on oak.

The panelled sides are held apart by jointed frames - morticed and tenoned this time - top and bottom, with a solid horizontal division between the drawers and the cupboard. These three horizontal carcass members are biscuit-jointed to the sides, and cut round the vertical facings which are also biscuited to the carcass sides.

A drawer divider is biscuited in place between bottom frame and fixed shelf.

The back is another mortice and tenoned frame, this time grooved to take loose panels - it extends down only to the fixed shelf, leaving the back of the drawer apertures open.

The drawers themselves are as conventional as they come, hand dovetailed and so on, and the bracket feet are made according to 18th century norms, complete with glue blocks. To allow the feet to sit wider than the carcass, a moulding is planted around the bottom of the carcass.

The top is slot-screwed to the top frame from below.

Sides and doors

Cut all parts from the sawn boards, then plane and thickness to finished sections.

I like to achieve a set of subassemblies as soon as possible, so the first job is to join the boards needed to make up wide components, in this case the panels, shelves and top. I biscuit these, but make sure that the biscuits are far enough away from,the ends not to be revealed when cutting the panel-raise.

Now the frames for the sides and doors can be made up. Remember to add an allowance to the width of each door's inner stile for the closing rebates.

I used a pair of tongue and groove router cutters made by The Wealden Tool Co. for the jointing - they cut a 12mm (^in) long by 6mm (ยก4in) thick tongue on the ends of the rails, and a corresponding groove in the inner edge of the stiles and rails, which takes both the rails' tongues and the dry-fitted panels.

Don't even think of using a handheld router for this job - a nice flat router table with a mitre guide is essential. Cut the tongues first, then the grooves. Leave the upper door rails square for this operation, cutting their arches, see panel, last of all before completing the groove - carefully! Before changing the cutter, groove a 150mm (6in) long piece of scrap.

"Don't even think of using a hand-held router for this job - a nice flat router table with a mitre guide is essential"

Panels

Now for the panel raising. This is another job for the router table, this time with a large diameter panel-raising cutter - this must have a guide bearing for the shaped work, although the straight edges are best fielded against a fence. These cutters are not safe at high speeds; only use them in variable speed routers, set to the slowest speed.

The aim is to produce a raising with a flat tongue which fits the groove in the stiles and rails; do this by gradually increasing the height of the cutter, checking for fit with the grooved piece of scrap -try this all the way round each panel, as the cut can vary. I find that two passes at each depth setting evens it out.

Make each pass across the ends of the panels first, then along the long grain, to avoid tearout.

That's all very well for the square side panels, but the broken arches of the door panels need a bit more work. Leave the panel square, but cut to width, while you field the bottom and sides of these - then complete the broken arch, see panel.

Finish-sand the panels, then glue-up the doors and side panels. If the rails' ends were square before assembly, it is hard to end up with an out-of-square panel, but I make these assemblies a little over-size to allow for final dimensioning after they are made up.

The side panels may now be rebated for the back, and the skirting board relief - if required - cut.

above: Finished in the white, and fitted up with hardware, ready for finishing

m\mi

0 0

Post a comment