Remove the hardware and apply the finish

1 Remove the hinges, magnetic catch and strike plate, and knob. Finish-sand all the parts.

2 Wipe on the stain. Using #8x3/4" flat-head wood screws, fasten the shelves to the plywood back. Apply the finish.

3Have a piece of '/s" glass cut to fit the door. (We secured the glass in the door frame with a fine bead of clear silicone sealant.)

4 Attach the hardware and door. Place the case back into the rabbeted opening, drill the holes, and then using #4x5/8" flathead wood screws fasten the back in place. Level and fasten the case to the wall. ♦

A sides 3A" 2W I8V2" C 2

'Parts initially cut oversize. See the instructions. Materials key: C-cherry, CP-cherry plywood. Supplies: MxVs" flathead wood screws, #8x3/4" flat-head wood screws, clear silicone sealant, 3/8" dowel pins 1" long, !/e" glass, stain, finish.

Buying Guide

Hardware. IViexlVie" solid-brass butt hinges;

3/8M-diameter polished knob, magnetic catch. Kit no.

71042, $6.25 ppd. Klockit, P.O. Box 636, Lake Geneva,

Wl 53147. Or, call 800/556-2548 to order.

See more. •.

  • gift and decorative 'MR accessory plans at
  • a href="http://www.MHidstope.vvDQdniad.ctni/girts.titinl">www.MHidstope.vvDQdniad.ctni/girts.titinl

Cut a kerf through each mitered corner of the door frame.

h hinge mortises

Cutting Diagram

'Splines

'Plane or resaw splines to Vs" thick and shelves ©to 1/2" thick.

1/4 x 24 x 24" Cherry plywood

DOOR

1/2 x 13/i6" mortise 1/32" deep

5/54" pilot holes 1/2" deep

13/16 x 13/16" brass hinge

We all have different storage needs for CDs, DVDs, or other electronic media. This timeless Arts & Crafts unit makes it easy You can quickly reshuffle the glass shelves inside to hold a variety of your favorite sights and sounds, with room left over for those valued collectibles that need protection.

1/2" rabbet

Left rear

Left front leg "V,

1/4" groove 1/2" deep, -centered

1/2" rabbet 1/4" deep

1/4" groove '/2'1 deep, centered

1/2" rabbet

Left rear

Left front leg "V,

1/4" groove 1/2" deep, -centered

1/2" rabbet 1/4" deep

1/4" groove '/2'1 deep, centered

Vfe" chamfer

V* x 11/4" mortise 1" deep (All mortises on legs , are same size.)

Vfe" chamfer side assembly

Vi x 11/4" mortise 1"deep (All mortises on legs are same size.)

Vi x 11/4" mortise 1"deep (All mortises on legs are same size.)

i/a" chamfer

1/4" groove 1/2" deep in' rails(§)and back rail©

1/4" groove 1/2" deep in rails ©and back rail(§)

21/4"

1/4" groove 1/2" deep in rails ©and back rail(§)

21/4"

Arc is 1/2" high at the midpoint of the rail.

i/a" chamfer

Arc is 1/2" high at the midpoint of the rail.

...mission furniture plans at hlt|i://uvood«tiB>e. woodnrsJI. com/misiupn.fitnil

Woodworking Tools and Installation Tips

Woodworking Tools and Installation Tips

There are a lot of things that either needs to be repaired, or put together when youre a homeowner. If youre a new homeowner, and have just gotten out of apartment style living, you might want to take this list with you to the hardware store. From remolding jobs to putting together furniture you can use these 5 power tools to get your stuff together. Dont forget too that youll need a few extra tools for other jobs around the house.

Get My Free Ebook


Post a comment