HttpwoodstoreWDodmalcotncointuphtnil

Back of door

Note: Stock is edge-joined using stopped splines at joints.

1/4" beads on top and bottom edge set to Vie"

Note: Stock is edge-joined using stopped splines at joints.

1/4" beads on top and bottom edge set to Vie"

19 shelf recess detail

Bottom side of shelf shown

STEP 1

Lay out hole location, and bore a W hole Vs" deep.

Bottom side of shelf shown

STEP 1

Lay out hole location, and bore a W hole Vs" deep.

Chisel remaining waste from notch.

First, construct the case

IRip and crosscut the case sides (A) and top and bottom (B) to the sizes listed in the Materials List.

2 Follow the two-step Drawing 2 to rout the front edge and ends of the top and bottom pieces (B).

3Mark the dowel-hole centerpoints on the ends of each case side (A), where shown on Drawing 1a. Using a doweling jig, drill 3/s" holes 9/i6" deep.

4Place dowel centers in the holes just drilled. Center the sides (A) between the top and bottom (B), where shown on Drawing 1. Clamp together the pieces to transfer the hole locations to the top and bottom pieces. (Depending on how many dowel centers you have, you might have to do one joint at a time.) Transfer the %" bit to your drill press, and drill 3/s" holes 9/i6" deep where marked.

5Sand the four pieces. Using 3/s" dowel pins l" long, glue, dowel, and clamp the sides between the top and bottom pieces, checking for square. Immediately remove excess glue with a damp cloth.

6To house the back (C), rout a -Vs" rabbet W deep along the back inside edge of the case frame (A, B). Square the corners with a chisel.

7Cut the back (C) to size. Drill the mounting holes in the back and case, and screw the back in place.

Looking for the perfect way to display those special keepsakes? Here's an easy elegant solution, featuring-simple dowel joints and spline-mitered doors. It goes together quickly from first cut to final coat.

W' hole for mounting

Spoon rack centerlines

7/64m hole, countersunk on back side, with a

hole in back side of case

W' hole for mounting

Spoon rack centerlines

  • i %" rabbet
  • 4 i Vi" deep, routed -

3y» s i after assembly

Thimble shelf centerlines

Thimble shelf centerlines

" dowel pin 1 " long

  • i %" rabbet
  • 4 i Vi" deep, routed -

3y» s i after assembly

" dowel pin 1 " long

3/s" hole

9/i6" deep (mating hole the same size)

exploded view

ES hole detail hole . 9/i6" deep

23/4"

3/a" rabbet Vi" deep, routed after assembly

3/s" holes 9/ie" deep 7/b" In from ends (mating hole the same size)

3/a" rabbet Vi" deep, routed after assembly

3/s" holes 9/ie" deep 7/b" In from ends (mating hole the same size)

V2" hole 1/i6" deep, drilled in back of door frame for strike plate

13/i6 x -We" brass hinge

V2 x 13/i6" mortise V32" deep

Ve glass cut to "

13/i6 x -We" brass hinge

V2 x 13/i6" mortise V32" deep

Ve glass cut to "

Vb" hole centered on xthe 3/4" flat front of(§)

V2" hole 1/i6" deep, drilled in back of door frame for strike plate door frame detail

routing the edges

Pilot bearing and face of -fence are flush.

Router table

Pilot bearing and face of -fence are flush.

Router table

STEP 1

STEP 1

Ve"

V4" round-over bit U^^J

door frame detail

Vs." spline groove 1" deep

Overall dimensions 37/s x 16 x 20"

Spline

Vs." spline groove 1" deep

Overall dimensions 37/s x 16 x 20"

Spline

V4" round-over bit U^^J

Woodworking Tools and Installation Tips

Woodworking Tools and Installation Tips

There are a lot of things that either needs to be repaired, or put together when youre a homeowner. If youre a new homeowner, and have just gotten out of apartment style living, you might want to take this list with you to the hardware store. From remolding jobs to putting together furniture you can use these 5 power tools to get your stuff together. Dont forget too that youll need a few extra tools for other jobs around the house.

Get My Free Ebook


Post a comment